Embedded Programming

Using Makefile rather than GreenHills (GHS) Multi .GPJ files

Anyone using Make rather than gbuild/Multi? If so, have any advise concerning doing this? Also, are there any translatio...

12 comments posted 18yrs

posted by zzmcclos

12 comments posted 18yrs posted by zzmcclos

TMS470 - Use of external bus to access memory and peripherals

I have tried to figure out from TMS470R1 documentation but it is not clear to me if what I want to do is possible. I wa...

0 comments posted 18yrs

posted by ih8sp4m

0 comments posted 18yrs posted by ih8sp4m

Force to load the module

Hi, I understand from the man page of insmod that it is not possible to force insmod if the symbol names in the module...

5 comments posted 18yrs

posted by karthikbalaguru79

5 comments posted 18yrs posted by karthikbalaguru79

PADS to Orcad PCB Editor

I'm making a circuit that uses part of an older design. I'd like to b able to keep the layout exactly the way it was on...

2 comments posted 18yrs

posted by joelbenway

2 comments posted 18yrs posted by joelbenway

reading in data from rs232 port, require to resend as an email

I am reading in some temperature sensor data, via RS232 (actually converted to USB via a CP2102 ), approx every hour in...

12 comments posted 18yrs

posted by sensecam

12 comments posted 18yrs posted by sensecam

SMS sender

Hi, I like to have my small hobby system sending status SMS to my mobile. I figure the easiest way is to just connect t...

4 comments posted 18yrs

posted by erikake

4 comments posted 18yrs posted by erikake

Cortex M3 with FreeRTOS

Is it a good idea to have Cortex M3 + FreeRTOS combo? Haven't heard of an discussion about Cortex M3 here lately. Henry

4 comments posted 18yrs

posted by hychan

4 comments posted 18yrs posted by hychan

18F452 RC oscillator mode

I read in ( 18Fxx2 DataSheet ) >>> http://ww1.microchip.com/downloads/en/DeviceDoc/39564c.pdf that I can use a Resistor...

7 comments posted 18yrs

posted by sebastiasebas

7 comments posted 18yrs posted by sebastiasebas

Polling a Port Pin for a specific amount of time

Hello all, I hope someone can help me as I am tackling my first ever work projec with 8051 and my previous experience i...

5 comments posted 18yrs

posted by picghaw

5 comments posted 18yrs posted by picghaw

"Number of BSCANs: 2 out of 1 200%"

Hi, I have added Chipscope to my design, but it seems to be incompatible because of BSCANS: Number of BSCANs: 2 out of...

0 comments posted 18yrs

posted by pbantunez

0 comments posted 18yrs posted by pbantunez

HELP! M16c/M32C M3A-0665 FoUSB emulator

Hi , I am looking for a Renesas M16c/M32C M3A-0665 FoUSB emulator I know it has been superseded by the E8A but for part...

0 comments posted 18yrs

posted by chris

0 comments posted 18yrs posted by chris

Building Toolchain for MIPS

Hi, I want to build toolchain for MIPS under cygwin. I am very confused when I configure the binutils. when I search th...

1 comments posted 18yrs

posted by huxuelei630

1 comments posted 18yrs posted by huxuelei630

Typical Cache Associativities

Hi, what are typical associativities of the instruction cache of today's embedded systems processors? Especially, I'm l...

0 comments posted 18yrs

posted by plfriko

0 comments posted 18yrs posted by plfriko

about ksoftirqd_CPU0 command

i have a question to my system.if my system boot,The command "ksoftirqd_CPU0" will eat too much cpu resources up to 99%...

0 comments posted 18yrs

posted by kobelai15

0 comments posted 18yrs posted by kobelai15

PCI SPI interface card

Hi All, I am developing an embedded product, and I need to talk to it using the MPU's SPI interface. I have been lookin...

16 comments posted 18yrs

posted by psd

16 comments posted 18yrs posted by psd