Embedded Programming

  1. Home
  2. Embedded Programming
16390 Threads Posts
to

Worth reading in Embedded Programming

Using priorities as a sequencing mechanism.

I've noted a certain style of programming that makes me uncomfortable, and I'm trying to articulate why.... Some people...
5 comments posted 18yrs
posted by jNoOhnS.PcAaMrter
5 comments posted 18yrs posted by jNoOhnS.PcAaMrter

Processors with remote programming / debugging

Hello, I am looking into potential embedded microprocessors to use for a one time project. About 2-3 units will be prod...
6 comments posted 18yrs
posted by lucasvickers
6 comments posted 18yrs posted by lucasvickers

problems while mixing C with asm

Hi, I'm newbie on the msp430 and I need to embed some asm in my C code. I'm working w/ the msp430F2418 and using the IA...
4 comments posted 18yrs
posted by barbosa.leonardo
4 comments posted 18yrs posted by barbosa.leonardo

SSC PLCEFN datasheet

Hello All! We have a lot of Intellon SSC PLCEFN ICs but no datasheet. Now I have to design a board with it. Could anybo...
0 comments posted 18yrs
posted by baranovus
0 comments posted 18yrs posted by baranovus

UART Initial state

Hi everybody, can anyone tell me what should be the potential at the tx and rx lines o uart at initial state.(whether i...
1 comments posted 18yrs
posted by svyamuna
1 comments posted 18yrs posted by svyamuna

Challenge: Motorola SC85370P

I've got a challenge for you guys: Can anyone tell me anything about a Motorola SC85370P? I'm quite confident that its...
19 comments posted 18yrs
posted by junk
19 comments posted 18yrs posted by junk

SBC with ADC, 1GE, and SATA2?

I'm lokking for a small (4x6", 6x8", range) SBC that has a reasonably good A/D converter (100+MSPS), at least one 1G et...
2 comments posted 18yrs
posted by mikemac
2 comments posted 18yrs posted by mikemac

RS422 interface

I am trying to interface two systems through RS422 link. There are onl four lines connected between them (tx+/- & Rx+/-...
20 comments posted 18yrs
posted by svyamuna
20 comments posted 18yrs posted by svyamuna

GNU LD fails to generate correct ARM Thumb veneer

good day people: i have been using GNUARM/Cygwin for some time now and i have not encountered a problem like this befor...
4 comments posted 18yrs
posted by adsouzp
4 comments posted 18yrs posted by adsouzp

Tranmitting AT command to GSM from 8051

Hello, I am developing 8051 based vehicle tracking system and Need SOS help o the following: Assemblly language code fo...
0 comments posted 18yrs
posted by lopa.banerjee2003
0 comments posted 18yrs posted by lopa.banerjee2003

I'm a bit lost on WinAVR (make problem?)

I've only been playing with WinAVR for a few days with this little project http://www.obdev.at/products/avrusb/hidkeys....
3 comments posted 18yrs
posted by mart_in_medina
3 comments posted 18yrs posted by mart_in_medina

Can You Guess Which Micro This Is?

I just bought a small embedded device (an iPod adapter for a car stereo). Being the inquisitive type, I popped open the...
25 comments posted 18yrs
posted by scottenaztlan
25 comments posted 18yrs posted by scottenaztlan

small data area and zero data area

Hi all, I understand that small data area and zero data area is in the RAM We have SDA as read only and read/write 1. w...
3 comments posted 18yrs
posted by mohankumar_beece
3 comments posted 18yrs posted by mohankumar_beece