Embedded Programming

16390 Threads Posts
to

[OT] -- Memory Vendors

Who's your favorite vendor for PC DRAM? I need some DDR modules for an older Dell. 512MB was a lot five years ago, but...
31 comments posted 17yrs
posted by tim
31 comments posted 17yrs posted by tim

microblaze and flash access

Hi, I am trying to access a flash device from a microblaze processor on a Spartan 3E device. In Xilinx XPS, I instantia...
0 comments posted 17yrs
posted by axr0284
0 comments posted 17yrs posted by axr0284

ADUC842 Keil ,xdata access ?

Hello to you all i'm trying to do an application with an ADUC842,i'm using the limited Keil C51 freeware environment my...
8 comments posted 17yrs
posted by bliscachiocciolinatiscalipuntoit
8 comments posted 17yrs posted by bliscachiocciolinatiscalipuntoit

Timing Measurement of PPC processor

Hi, I'm running VxWorks Os on a MPC 8323 processor. The VxWorks timers are based on the OS ticks (several mili seconds)...
2 comments posted 17yrs
posted by anwar_pc
2 comments posted 17yrs posted by anwar_pc

I2C simulator

Hi all, I want to learn 'how to program an I2C device' . I am trying to find a simulator for an I2C device which I can...
4 comments posted 17yrs
posted by wills.kingspanama
4 comments posted 17yrs posted by wills.kingspanama

Shelf life of solder

Managed to fry a voltage regulator earlier today attempting to solder it in place. It just wasn't wetting properly and...
9 comments posted 17yrs
posted by andrews
9 comments posted 17yrs posted by andrews

Designing for and soldering a tiny BGA

Hi folks, I need to design a small board and get it fabbed (as cheap as I can - I have little money) which needs to con...
82 comments posted 17yrs
posted by ian
82 comments posted 17yrs posted by ian

How can I transplant spcaview to ARM9

Hi, everyone. The past few days I have been put in to transplant spcaview to ARM9. If I'm If I am successful, I can see...
3 comments posted 17yrs
posted by jiangzhe78
3 comments posted 17yrs posted by jiangzhe78

Multiple servers with lwIP or uIP

Hi, I just want to upgrade an 8051 application written fully in assembler, so I'm facing starting from scratch. After w...
2 comments posted 17yrs
posted by oscar
2 comments posted 17yrs posted by oscar

Acess ARM9 hardware timers ( C and Linux )

Hello everybody, I'm new to embedded linux development. I want to write some routines that need 1uS timer resolution. I...
6 comments posted 17yrs
posted by jimnorton
6 comments posted 17yrs posted by jimnorton

How to change the entry point for a boot loader

Hi All, I have a KMC board with mips VR4131 processor. The target board already having cmon boot loader on flash. Now I...
0 comments posted 17yrs
posted by lucky.veeramallu
0 comments posted 17yrs posted by lucky.veeramallu

Read MPC855 Memory with Wiggler?

Hello everyone, I'm very new to embedded systems, and debugging them. Im teaching myself and learning a lot on the way....
0 comments posted 17yrs
posted by ramblinpeck
0 comments posted 17yrs posted by ramblinpeck

Richard Stallman is responsible for the shrinking economy

Richard Stallman is responsible for the shrinking economy in US and Weston Europe GNU licenses and open source software...
405 comments posted 17yrs
posted by bigbrownbeastiebigbrownface
405 comments posted 17yrs posted by bigbrownbeastiebigbrownface