However installing Ethernet on the MCU of that class is not a very good idea. It will be the incomplete realization with the poor performance and the compatibility problems.
Vladimir Vassilevsky
DSP and Mixed Signal Design Consultant
formatting link
Didn't find your answer? Ask the community — no account required.
D
DJ Delorie
Not built in, but R8C/24 (16bit, 48k flash, 52-LQFP, $3.60 qty100) plus a CP2200 (48-TQFP, $5.62 qty100) fits your other specs. The R8C is available in various flash/package combinations, if you want to fine-tune the cost/flash balance.
Alternately, the M16C/30P - 16bit, 96K flash, 100-LQFP, $3.78 qty100.
If you allow microchip peripherals, the ENC28J is $3.54 qty100.
To save even more money, you can build gcc et al for the r8c/m16c/m32c platform and not have to pay any license fees for development tools. The r8c/m16c/m32c platform has a number of other development tool packages available also, like NC30 and IAR, and the gcc tools are supported via the FSF's mailing lists and two commercial support companies. (just in case anyone was wondering ;)
D
DJ Delorie
Also, CP2201 is cheaper - $4.77 qty100 - if you don't mind leadless packages (28-QFN).
S
Spehro Pefhany
Hi, all.
What current low-cost (USD $5-$10 in 1K) options do I have for a flash microcontroller (8/16/32 bit) with a built-in 10-base-T ethernet MAC+PHY, and reasonable program memory (say 32K or 64K minimum)?? Other than Microchip.
Best regards, Spehro Pefhany
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
G
Grant Edwards
There are also 32-bit Renesas H8/300 parts (3062B "value series") with 128K of flash that come it at about $4.00 in low quantities.
Grant Edwards grante Yow! ... I don't like
at FRANK SINATRA or his
visi.com CHILDREN.
J
Jim Granville
Try the ASIX AX11015 - that's quite a capable 8 bit (100Mips) CPU with the ethernet 10/100Mbps MAC+PHY, and 128-512K Flash.
Claims $4.99/10K, so likely to be at the cheaper end of your price.
formatting link
formatting link
-jg
O
Oliver Betz
BTW: did you intentionally not set a Followup-To?
Maybe some new Coldfire derivatives, I'm not sure as IO don't need Ethernet. Atmel AT91SAM7X128 IIRC not "with MAC+PHY".
Oliver
Oliver Betz, Muenchen (oliverbetz.de)
S
Spehro Pefhany
Thanks, Jim. I've run into that one in an IP camera, but didn't know the source. It even has the core regulator on chip.
I've also found an HC12 with the peripherals. Thanks, guys.
Best regards, Spehro Pefhany
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
O
Oliver Betz
[...]
Hmm... Make sure that the NE64 is available as long as your product will be produced.
And consider broadcast messages - they can create much load for small micros.
Oliver
Oliver Betz, Muenchen (oliverbetz.de)
P
pbreed
Try the Freescale MCF52234
32 bits 256k flash, 32K ram, a/d i2c, spi, uarts, timers anethernet MAC and PHY.
Paul
R
RobertTeufelDUS
Hi,
there is nothing that beats the LPC2364 in price / performance. The only catch right now, limited availability. No on-chip PHY but an ARM7 with 128k Flash 34k SRAM with Ethernet and USB for $3.99 @ 10k. Have a look at Digikey although they are out of this device but the pricing is there for smaller quantities. You might get a 128k Flash ARM7 cheaper than a 64k PIC althoung it has more than 10 times the performance :-)
Robert
S
Spehro Pefhany
It's attractive. What's the best deal for a PHY (only need 10-base-T)? ADM7001X? I guess the availability is a good match anyhow.
Best regards, Spehro Pefhany
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Join the Discussion
Have something to add? Share your thoughts — no account required.
Didn't find your answer?
Ask the community — no account required
Report Content
You are reporting this content to the moderators. They will look at it
ASAP.