On the datasheet for the STP80PF55
- posted
16 years ago
On the datasheet for the STP80PF55
Well it's reasonably obvious what it is, it's the voltage required between the gate and the source to produce the specified current in the draon source connection. Have you not used one before? It's an honest question, asked with all due respect.
Sincerely,
Robert.
kell wrote:
I suggest that Vgs is probably 10V, but that graph is so screwed up you're probably better off to ask ST for a correct one. At least the Y axis is wrong in title, and probably in values by 10:1.
Best regards, Spehro Pefhany
-- "it\'s the network..." "The Journey is the reward" speff@interlog.com Info for manufacturers: http://www.trexon.com Embedded software/hardware/analog Info for designers: http://www.speff.com
It's a pretty strange looking graph but, if I understand, the horizontal axis represents Vgs's from 2.5V thru ~7V. The vertical axis represents the amount of drain current (Id) required to create an arbitrarily chosen 5V drop (Vds). Since there is a well defined curved line, I suppose that proves that Rdson is fairly static for a given Vgs. I don't know why they felt the need to make a puzzle out of it. This looks allot like the work of "The Center of Confusion". ;-)
One hint that something is seriously wrong is that a graph called "Static drain-source on resistance" does not have ohms as the units for the dependent variable. A second hint is that if you interpret the Y axis as ohms, it's about 10:1 too high to match the typical Rds(on) figure of 16m ohms. A third hint is that Vgs is not stated. Garbage.
Best regards, Spehro Pefhany
-- "it\'s the network..." "The Journey is the reward" speff@interlog.com Info for manufacturers: http://www.trexon.com Embedded software/hardware/analog Info for designers: http://www.speff.com
Oops, I'm sorry. I was looking at the graph above it.
Bad caption? Looks like the substrate diode curve to me.
John
They duplicated that curve from elsewhere. The identical graph (with the identical ID number) shows up in Figure 11, with the correct caption.
BTW, have you done any work with Philips MOSFETs? I'm looking for a small (preferably smaller than DPAK) low-voltage (eg. 30V) MOSFET with a gargantuan SOA for handling one-shot exponential-decay pulses.
Best regards, Spehro Pefhany
-- "it\'s the network..." "The Journey is the reward" speff@interlog.com Info for manufacturers: http://www.trexon.com Embedded software/hardware/analog Info for designers: http://www.speff.com
I'm no pro but will take a shot at answering this...
Look at figure 3 to understand figure 6. I'll guess the Vgs for figure 6 about 4Volts.
Vgs of 10V on figure 3 is probably just to show the max test range. It's confusing. D from BC
There you go, that explains it. Thanks John & Spehro.
No, I don't think I've used any Philips fets. Do you need to absorb a lot of energy? Maybe use a series resistor and a tiny, low Rds-on fet?
John
Yes, I've been looking at doing that (it's even possible to get SMT WW resistors) but it might not be acceptable for other reasons. The total energy is not huge, perhaps 1J.
Best regards, Spehro Pefhany
-- "it\'s the network..." "The Journey is the reward" speff@interlog.com Info for manufacturers: http://www.trexon.com Embedded software/hardware/analog Info for designers: http://www.speff.com
You could probably dump a joule into a SOT-23 fet, certainly into a power-pad SO-8 or one of the 6-lead power-pad SOT-23's.
How about a pcb trace to soak up some of the energy? If you had a tiny
20 mohm fet, and put 20 mohm of pcb trace in series, that cuts the fet stress by 2:1. That would be about 0.25" of 6 mil, 1 oz trace.Get some SOT-23 fets and some caps and dump joules until the fets fry. Fun!
John
ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.