LED indicator for bad MOVs

Going to Brickwall or Surgex for a discussion about MOVs is like going to Rush Limbaugh for an honest analysis of Hilary. Above is this idea that MOVs absorb surges. Not true. They are called shunt mode devices for good electrical reasons. MOV is rated in joules much like wire is rated in amps. Joules determine how much surge gets shunted (diverted) just like wire. Unlike wire, MOVs degrade. And as joules increase, the degradation decreases exponentially. Notice from here on the numbers that series mode protectors forget to provide. No number is how one 'lies by telling half truths'. It's called spin.

Some discuss life expectancy of MOVs is because many plug-in protectors are so grossly undersized. If any MOV protector vaporizes, then two things have happened: 1) the protector was grossly undersized. 2) MOVs operated in an unacceptable mode that even its own manufacturer does not define. Charts for life expectancy rate 1, 10,

100, 1000, and 10000 transients. This is life expectancy where threshold voltage eventually charges by 10% - no vaporization. There is no curve for zero transients - which are what happens when MOVs vaporize.

Brickwall and Surgex also forget to mention a wire that carries destructive surges completely around -bypasses - their protectors. Again, Rush Limbaugh type spin where they conveniently forget to mention certain critical facts - assume a reader is that naive.

Brickwall and Surgex series mode protector are supplemental protection. To be effective, a building must have shunt mode protection. What is shunt mode protection? Often using MOVs because MOVs are so effective. How can this be if MOVs stop or absorb surges? They don't.

MOVs fail when a protector is not properly installed - undersized by a human. This problem is common with plug-in protectors that don't claim effective protection anyway. When MOVs vaporize or blow that thermal fuse - that causes the light to change - then you know that protector was grossly undersized, and failed leaving electronics completely exposed to that last surge.

However when selling plug-in protectors to the naive, then profits are higher by grossly undersizing those MOVs. The naive human will foolishly assume, "The protector sacrificed itself to save my computer". Reality: computer's internal protection saved it.

A quote directly from an MOV datasheet:

The series 14 MOV is rated for 150A standard transient pulses for

10,000 times. So where is this degradation? It exists. And degradation is irrelevant when properly sized.

We install 'whole house' protectors for typically destructive transients that occur once every eight years. Smaller transients (that are often nothing more than noise) are made irrelevant by protection already inside every appliance.

Numbers and facts that series mode protectors forgot to menti> It can be either and the data sheet should state whether that is a 'per

Unfortunately, the only reliable way is to determine if the voltage has ever exceeded what the clamping voltage should be. Actually measuring the clamp voltage can be done in som ecases.

I have seen how this is done:

The product with the MOV has a fuse that is assumed to blow if the MOV fails. Maybe the fuse is a thermal one placed against the MOV - I don't remember that well. Supposedly maybe, not many MOVs fail open except in response to something that would blow that fuse.

The indicator lamp goes across the fuse. If the MOV is open rather than shorted, then you need some load in parallel with the MOV to draw current through the indicator lamp.

- Don Klipstein ( snipped-for-privacy@misty.com)

Hello Stefan,

With MOVs it isn't this easy. When it has gone open that means the damage may have already been done, that it let some surge pass through.

MOVs are like bank accounts. They offer x many Joules of 'protective power absorption'. But you never know how much is left in the account. Will it be enough for one more surge? That's one reason why I don't use them in my designs, usually.

A LED could tell you whether it failed. But that may be too late for whatever was connected.

Regards, Joerg

I heard that the joule limit of an MOV is not lifetime, but closer to per-incident. Short of bad incidents severe enough to make the thing hot enough to degrade, they don't degrade from absorbing surges.

I try Google:

Says MOVs do not degrade if they don't get heated to the point of a thermal runaway condition or to temperatures at which cause a significant rate of degradation.

Although this article does mention surge history as a factor in degradation of MOVs, the same sentence emphasizes surges that are in excess of ratings. The paragraph with that sentence makes it appear to me that the degradation is from temperature-related diffusion.

However, there is still the problem of an MOV experiencing a surge failing open before any fuse upstream of it opens and before the surge is over. That should only be a problem with especially catastrophic surges.

- Don Klipstein ( snipped-for-privacy@misty.com)

Hello Don,

It can be either and the data sheet should state whether that is a 'per event' or 'over the lifetime' rating, and under which test scenario it was derived. According to most documents I read they do degrade even when not exposed all the way into the thermal run-away region.

There will always be local heating even with a massively parallel structure. It's a matter of how much and not linear. But AFAIK they will still age with non-severe surges that are significant enough.

Yes, it's the same problem as with the oil pressure light in a car. When that light comes on it is often too late for the engine.

Regards, Joerg

They are (variable) resistors. P = I^2R. That's heat, created as electrical energy is *absorbed*. When more energy is absorbed by the MOV than it can dissipate, the MOV fails, sometimes spectacularly. Stating that MOV's do not absorb surge energy is an untenable position.

Ed

thanks for the input!

Somehow this thread makes me feel more comfortable to work with MOV?s considering I use quality MOV?s at a high rating. To protect the MOV?s somewhat, different stages are mentioned to reduce the size of the surge by limiting it?s speed using HF inductors or LC snubbers. Any idea on values to get a better 117AC line protection? Put these after the Mov?s as

2nd stage or make them 1st stage protecting the MOV?s also?

I feel that with $40 well spend on parts I?ll get a much better protection than these $100.00 devices. I?m note looking for fine noise reduction, just keeping the big bang out of my electronics.

Stefan V

MOV connection to earth determines quality of that protection. Why are so many MOV based protectors so undersized? Because plug-in protectors don't have an effective earthing connection. No earth ground means no effective protection. So why installed enough joules? Effective MOV based protector that is also sufficiently sized is 'whole house' protectors.

'Whole house' protectors being so effective and so inexpensive that a telco installs one, for free, on your phone service. But again, protector is only as effective as its earth ground. Earthing is another essential part of protection that those application notes forgot to discuss.

To appreciate the most critical component of a protection system, learn about that most essential component - single point earth ground.

Numerous industry professional citations, concepts, experience, numbers - about one days worth of technical reading describe protection in hyperlinks previously posted in alt.comp.periphs.mainboard.asus on

30 Mar 2005 entitled "UPS unit needed for the P4C800E-Deluxe" at:

Meanwhile, if c> thanks for the input!

Hello w_tom,

ROFL! That was a good one. Almost spilled my coffee when I read it. Once I had to do some FFT algorithm tests and I just used the radio as an arbitrary source. It happened to be Rush. Sometimes you could see the spectral average of his voice slowly drift upwards. That was a sure sign that he was slowly getting upset about a topic he just started.

mode

With all due respect, shunt mode devices are called shunt mode because the do dissipate energy. Except when it's a wire of infinite conductivity. MOV transfer spike energy into heat.

Well, yes, but that's the same with almost every product. My SUV came with truck tires so they have lasted 55000 miles by now. Still lots of thread left on them. The tires on our sedan were long gone by then because they were smaller and less durable car tires. Of course, the truck tires cost a lot more.

I have nothing against MOV if they are large enough (they usually aren't). But relying on them to prevent over-voltage isn't my cuppa tea. You cannot select them too close to the rated rail or line voltage since they aren't as precise as a voltage reference, meaning they could 'seep', get hot, age faster and then one day, 'Kaboom'. But if you have to protect against some substantial surge as a first line of defense they may be the ticket.

Regards, Joerg

Hm.. Top post...

Why not improve your outside protection first?? A simple airgap with a solid ground connection maybe. If that does not survive, what else wil?? Or else the gas discharge tubes,both make a nice path to ground,without to much raise in line voltage. Just blocking with an outside inductor will only help for the small discharges,the bigger ones wil just jump across the inductor. Anything getting past the tube or gap, might be stopped by the fuse/inductor/MOV combination inside the building. Even if the MOV shorts, at least it protects by blowing the fuse. Of course fuse and MOV must be replaced after a heavy hit,or a number of smaller ones. There is no way you can protect against a full hit,but at least such a combination should give you the best protection.