read-only Filesystem on boot?

Hi Folks,

I have an ADI:Coyote board that I am trying to get up with the Snapgear

3.1.1 1.4 kernel.

I have compiled everything from scratch and chosen all the defaults. When I download and boot, it says that the filesystem is readonly, and then when it tries to run init it goes off into the weeds. I have uncompress the ramdisk and mounted it on my PC linux system via the loop device and it looks fine.

Any help would be appreciated....

Here is the console log:

ip_address -l 192.168.0.100 -h 192.168.0.4 IP: 192.168.0.100/255.255.255.0, Gateway: 0.0.0.0 Default server: 192.168.0.4, DNS server IP: 0.0.0.0 RedBoot> looad-r -v -b 0x01600000 zImage Using default protocol (TFTP) Raw file loaded 0x01600000-0x016ac563, assumed entry at 0x01600000 RedBoot> load -r -v -b 0x00800000 ramdisk.gz Using default protocol (TFTP) Raw file loaded 0x00800000-0x009dd9c9, assumed entry at 0x00800000 RedBoot> g -n 0x01600000 Uncompressing Linux................................................. done, booting the kernel. Linux version 2.4.24-uc0 (mgg@linux) (gcc version 3.2.1) #1 Sat Jun 19

19:31:29 PDT 2004 CPU: XScale-IXP4xx/IXC11xx revision 1 Machine: ADI Coyote Residential Gateway Warning: bad configuration page, trying to continue alloc_bootmem_low memtable_init On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS1,115200 root=/dev/ram0 initrd=0x00800000,8M mem=32M@0x00000000 Calibrating delay loop... 535.75 BogoMIPS Memory: 32MB = 32MB total Memory: 22580KB available (1140K code, 234K data, 232K init) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX PCI: bus0: Fast back to back transfers enabled Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en abled ttyS00 at 0xff000003 (irq = 15) is a XScale UART ttyS01 at 0xff001003 (irq = 13) is a XScale UART RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NetWinder Floating Point Emulator V0.97 (double precision) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 8192K VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 232K (nil)(null)infINFnanNAN.,@$@Y@Ã^A-×"CAÃy7à?F"¸µµnM8Oé?ùõZ,wHù02uOÝs¿
Reply to
Earthlink
Loading thread data ...

ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.