Embedded Programming

bus allocation strategy

Hi everyone, I'm not sure if here's the best place were to talk about this subject and I'd be glad if someone post the...

19 comments posted 11yrs

posted by al.basili

19 comments posted 11yrs posted by al.basili

measuring current consumption in uC with very low power modes

Hi to all, often i have to measure the current absorbed by small circuits,in battery appplications Normally i deal with...

9 comments posted 11yrs

posted by blisca

9 comments posted 11yrs posted by blisca

Disk imaging strategy

Hi, I'm writing a bit of code to image disk contents REGARDLESS OF THE FILESYSTEM(s) contained thereon. This doesn't ha...

95 comments posted 11yrs

posted by this

95 comments posted 11yrs posted by this

Seeking advice: Getting into entry-level embedded engineering

Hi all, I'm looking for advice about being an embedded engineer. I have a BS and MS in electrical engineering, an MBA a...

16 comments posted 11yrs

posted by ushakil

16 comments posted 11yrs posted by ushakil

Android & iOS tools

A customer wants both apps in 2 weeks. Gee, i can barely do Android in two weeks. iOS is completely new to me. I can ru...

17 comments posted 11yrs

posted by edward.ming.lee

17 comments posted 11yrs posted by edward.ming.lee

How to write a software description document?

I have written software for an embedded system. All commands are received b y UART. Now I must create a document that d...

11 comments posted 11yrs

posted by skolpojken72

11 comments posted 11yrs posted by skolpojken72

Parsers for extensible grammars?

Hi, [I probably should direct this at George... :> ] I'm writing a command parser. Some set of commands are "common". B...

43 comments posted 11yrs

posted by this

43 comments posted 11yrs posted by this

USB Cable for Programming Xilinx FPGA (Spartan 3)

Hello everyone, I would like to know if we can use a general purpose (available off-the-shelf at popular stores) USB to...

6 comments posted 11yrs

posted by anand.paralkar

6 comments posted 11yrs posted by anand.paralkar

x86 real mode

Hi, What are the most conservative, *practical* expectations I can make living in x86 real mode: TEXT of 64K and DATA o...

64 comments posted 11yrs

posted by this

64 comments posted 11yrs posted by this

Why can't I load code with the debugger ?

My target board is wired with Renesas Microcontroller Unit M16C/6N5 Group. Device M306N5FC. The target board is connect...

2 comments posted 11yrs

posted by 102059

2 comments posted 11yrs posted by 102059

file format for .RUN in MPC5566?

In .run file Internally how to calculate checksum and which address will be assigned the data.In internal file what is...

0 comments posted 11yrs

posted by 102034

0 comments posted 11yrs posted by 102034

validity of ... reasons for preferring C over C++

> PS I am (in the context of this question) NOT interested in > - whether a reason is valid (please start a different t...

111 comments posted 11yrs

posted by nobody

111 comments posted 11yrs posted by nobody

reasons for preferring C over C++

"Small-chip programmers are better off using C++ instead of C." Take small-chip as =

44 comments posted 11yrs

posted by wouter

44 comments posted 11yrs posted by wouter

How to read a 32-bits hw counter on 8-bits microcontroller

In the thread above about RS485 driver enable, always originated by me, some new and interesting (for me) techniques ha...

8 comments posted 11yrs

posted by pozzugno

8 comments posted 11yrs posted by pozzugno

Two-wires RS485 and the driver enable problem

I have a multi-drop two-wires RS485 bus. One node is the master and all the others are slaves. The master is the only n...

65 comments posted 11yrs

posted by pozzugno

65 comments posted 11yrs posted by pozzugno