Embedded Programming

Trying to reverse engineer a Palm IIIx--can't figure out the up/down buttons!!

Hi, Yeah, I know the Palm IIIx is kinda old, but...I want to overwrite the OS (already have my own little piece of firm...

7 comments posted 18yrs

posted by adirondackmtn

7 comments posted 18yrs posted by adirondackmtn

Interrupt latency

Hi, I am writing my own real-time kernel for x86. Now I face something really strange (or may be rather it's not; it ha...

26 comments posted 18yrs

posted by spamtrap

26 comments posted 18yrs posted by spamtrap

File - partially Read-Only and partially Write-Only

Hi, In Linux, Is it possible to make 25% of a file contents to be 'Read Only' and the remaining 75% of the file contents...

8 comments posted 18yrs

posted by karthikbalaguru79

8 comments posted 18yrs posted by karthikbalaguru79

Need help in SDR

Good morning,my name is Emad i leave in egypt ,i taken BSC in communication & electronics engineering with GPA "A" an n...

1 comments posted 18yrs

posted by eng.emadsamuel

1 comments posted 18yrs posted by eng.emadsamuel

Orcad BOM errors

I am used to Orcad spitting out multiple lines in the BOM for the same part which happens when every property of the pa...

0 comments posted 18yrs

posted by gnuarm

0 comments posted 18yrs posted by gnuarm

With a PC based on the Intel® Pentium® 4 Processor with HT Technology†, you get advanced performance and mult itasking capabilities for today's digital home ...

With a PC based on the Intel=AE Pentium=AE 4 Processor with HT Technology=86, you get advanced performance and multitas...

0 comments posted 18yrs

posted by sehanran

0 comments posted 18yrs posted by sehanran

Physics for programmers

Just found this, seems to have some good links, but I'm not a physysist http://reddit.com/info/6c6r6/comments/ martin

2 comments posted 18yrs

posted by mart_in_medina

2 comments posted 18yrs posted by mart_in_medina

Off-the-shelf temperature controller modules

I'm looking for a small embedded controller module which can interface directly to a thermocouple (K-type, I think) and...

11 comments posted 18yrs

posted by fred

11 comments posted 18yrs posted by fred

Orcad vs. Open Source

I am trying to finish up a board layout and I have been making changes to facilitate the routing of traces without so m...

27 comments posted 18yrs

posted by gnuarm

27 comments posted 18yrs posted by gnuarm

beginning arm

hi i would like to purchase an arm dev. board to learn arm architecture an assembler and to improve my career prospects...

4 comments posted 18yrs

posted by eecoding

4 comments posted 18yrs posted by eecoding

Again which micro controller for electromagnetic noisy environments

Dear Friends, I am about to chose a micro controller for another power control unit application. Earlier I used Renesas...

0 comments posted 18yrs

posted by narender

0 comments posted 18yrs posted by narender

Easy Question about USB Hardware Design

I'll keep this really simple: Would it be ok to use +3.3V on the VCC of a Host port, if you only expect to use a single...

15 comments posted 18yrs

posted by Quiller123

15 comments posted 18yrs posted by Quiller123

pic tmr0 question

Hi, There is a PIC16C620A microcontroller which is running at 16MHz. In which time intervals starts the TMR0 interrupt...

0 comments posted 18yrs

posted by ds0163

0 comments posted 18yrs posted by ds0163

Looking for online Flex PCB manufacturer

Hi, This is the first time I am venturing into flex PCB territory. The PCB houses I normally use do not do flex PCBs. I...

4 comments posted 18yrs

posted by nobody

4 comments posted 18yrs posted by nobody

Notes from AVR32 UC3 seminar

I recently attended a seminar on the MCU version of the AVR32, known as the UC3. To say that I was impressed would be a...

8 comments posted 18yrs

posted by englere_geo

8 comments posted 18yrs posted by englere_geo