Embedded Programming

RTS/CTS flow control

I have to work with a third party device which requires RTS/CTS flow control over RS-232. Is there any official recomme...

19 comments posted 14yrs

posted by nospam

19 comments posted 14yrs posted by nospam

Modification of Linux driver atmel_serial.c to use it in synchronous mode with external clock?

Hi, I need to use the USART in AT91SAM9260 working under Linux OS (quite old 2.6.29.3 version, due to compatibility wit...

1 comments posted 14yrs

posted by wzab01

1 comments posted 14yrs posted by wzab01

Distributed I/O nodes on CAN/485 for home networking

Hi, I am looking for a cheap, low power micro board that has some i/o (mostly digital) and a communication bus suitable...

6 comments posted 14yrs

posted by pradeep.chandran

6 comments posted 14yrs posted by pradeep.chandran

ARM core, PWM, USB

Any time someone posts something like this I think "oh yea, go hit the web sites, you lazy @#%$". But this time it's di...

10 comments posted 14yrs

posted by tim

10 comments posted 14yrs posted by tim

Device driver template?

Hi, Does anyone have a good reference to device drivers? Linux device drivers seem to be well documented although I hav...

6 comments posted 15yrs

posted by peter_goddard

6 comments posted 15yrs posted by peter_goddard

U2IO problems

We use the U2IO USB interface for getting GPI and GPO from the Infocaster software. Through the U2IO interface the Info...

0 comments posted 15yrs

posted by progonyie

0 comments posted 15yrs posted by progonyie

Support duration?

Hi, What sort of policies do (contract/free-lance) folks follow for post-release support? As a matter of policy, I fix...

8 comments posted 15yrs

posted by nowhere

8 comments posted 15yrs posted by nowhere

Re: Is FORTH waxing or waning in the embedded world ?

> Tentative conclusion: the whole world's going crazy, so Forth must be > waxing. > > -- > Joe Sounds like a Troll me me...

0 comments posted 15yrs

posted by jasondamisch

0 comments posted 15yrs posted by jasondamisch

VFP11 Veneers (GCC ARM)

Hey y'all -- I was just looking through the disassembly of a project I'm working on around an ARM9 (NXP LPC3250) under...

1 comments posted 15yrs

posted by rgaddi

1 comments posted 15yrs posted by rgaddi

Data Logger

I am looking for a data logger device, to use in an embedded project I'm working on. Basically, this device is to log i...

9 comments posted 15yrs

posted by kbforfb

9 comments posted 15yrs posted by kbforfb

Benchmarking C compilers for embedded systems

I'd like to compare C compilers targetting embedded systems - the kind that only have a few KB of RAM, etc. However the...

21 comments posted 15yrs

posted by pkk

21 comments posted 15yrs posted by pkk

Unaligned memory access through pointer in cortex-m3

Hi friends, I am using stellaris LM3s6965 micro-controller, Keil (MDK-ARM 4.20) as IDE. I want to know the alignment re...

7 comments posted 15yrs

posted by kiishor

7 comments posted 15yrs posted by kiishor

race condition? between relays and 89C51 uC

hello everyone, I have a RS485 based slave relay driver with 8 relays. The relays turn on at logic 0. Since the 89C51 h...

7 comments posted 15yrs

posted by mansoor.naseer

7 comments posted 15yrs posted by mansoor.naseer

RANT: Embedded Devlopers And Stinky Documentation

Hi All, I would much rather not spend any time on a Friday night ranting about computer stuff, but today I had enough r...

26 comments posted 15yrs

posted by jaibuduvin

26 comments posted 15yrs posted by jaibuduvin

Re: ATJTAGICE3 wont detect on XP

BobG skrev 2011-09-14 21:16: > I tried the jungo 10.2 stuff from atmel beta, but I get 'unknown > device'. Anyone runnin...

1 comments posted 15yrs

posted by ulf

1 comments posted 15yrs posted by ulf