Spent the weekend testing whether metal really blocks radio waves and the results surprised me

Nov 10, 2026 Last reply: 1 week ago 5 Replies
Jump to replies (5)

So I've had this arguement going with a buddy for months about wether a solid metal sheet kills a radio signal completly. I finally grabbed a cheap RTL-SDR dongle I had in a drawer, hooked it to an old roof antenna, and did some testing in the garage. He was convinced that a big piece of sheet steel woud be a hard wall for any signal. Turns out it's messier than that. My local FM broadcast station dropped to basicly nothing behind the full sheet, no shock there. But the WiFi from my router, at 2.4 GHz, still came through faintly on the other side of a smaller steel panel with seams and a gap at the bottom. The wavelength matters a lot, and openings or gaps leak like crazy. Even a hole the size of a cable pass-through let a surprising amount through. The takeaway for me is that 'blocks radio' isn't a yes or no thing, it depends on frequency, thickness, and how many gaps you've got. Now I understand why my garage door opener struggles when the car is parked just right but works fine otherwise. Solid metal reflects and absorbs, but nothing in a real garage is a perfect sealed box.



Gonna try a proper faraday cage test next with a mesh screen and see how fine the mesh needs to be before it actually stops things for real.


I ran into the same thing years back when I tried to stop my neighbor's ham radio from bleeding into everything in my office. I lined one wall with galvanized flashing from the hardware store, overlapped the seams maybe an inch, and figured that was that. His signal on some bands dropped alot, but the two meter stuff he used most evenings still snuck in thru the overlap I was lazy about. Once I actually soldered a strip of copper across each joint it went quiet for good. The mesh test you're planning is fun. I did mine with window screen material stretched over an old picture frame and it knocked down my own WiFi router placed a foot behind it, but Bluetooth earbuds still connected fine. The spacing on the mesh was way too wide for those higher frequencies.

One thing that surprised me was how the cable entry point was the real culprit in my setup. The coax came in through a rough hole in the siding with no bonding, and grounding the shield to a proper ground rod outside cut the noise more than the flashing did. Might be worth checking how your antenna feed enters the garage before you build anything bigger.

My experiance went the other direction almost. I wanted to block my own router's signal from reaching the neighbor's shop so his smart TV would quit fighting my wifi, so I built a little enclosure out of hardware cloth from the farm store, the kind with quarter inch openings. Figured mesh would be easier than wrestling with sheet metal. Well, at 2.4 GHz those quarter inch holes were apparantly still plenty big, because the signal only dropped by about half, measured with a cheap wifi analyzer app on my phone. I double checked by wrapping a steel cookie sheet around the router as a joke and it basically blanked the signal to the next room. So for anyone planning the mesh test, the opening size relative to the frequency seems to be the whole story, and my quarter inch was way too coarse. The mesh did work great for blocking AM radio through a bedside clock, though, which is a much lower frequency. Fun how one material behaves totally differently depending on what's hitting it. If your faraday test needs to work at wifi frequencies I'd start with much finer mesh than you think you need, or just use solid metal with taped seams like I ended up doing in the end.

Back in the day the old TV repair guys used to talk about this stuff all the time. A cookie sheet with foil wrapped around a radio in a shoebox was my science fair trick as a kid, worked great on AM, useless on anything higher. These days I keep a cheap pocket radio around and just walk it around the shop when I'm chasing a dead spot or figuring out where somethig is leaking in. AM bands are long enought in wavelength that even sloppy shielding looks perfect, so don't get fooled by that part of your mesh test. Anything around 2.4 GHz will find every gap you've got.

For me the thing that finally made shielding click was a roll of adhesive copper foil tape from the hobby shop. I was lining the inside of an old metal toolbox to make a little shield box for a project, and the seams were the whole problem. Where the foil overlapped itself and stuck good, signals stopped. Where I got sloppy and left a corner barely touching, the radio came right back. That stuff sticks to itself well enough that you can fold it over an edge and get a real bond instead of hoping two pieces kiss. If your mesh test drives you crazy trying to get good contact at the joints, that tape is the cheap answer. Curious how fine a mesh you end up needing.

Funny timing, I was dealing with this last week trying to figure out why my tire pressure sensor tool would only relearn sensors when the car sat in one exact spot in the driveway. Moved it two feet and nothing. Turns out the metal awning over the porch was bouncing the signal around just enough. If you do the mesh test, try wrapping your dongle in the mesh while it's running and watch the signal meter live. Way easier than guessing, you can slide a single layer around and see exactly where it stops mattering.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required