Embedded Programming

AT91RM9200 bootloaders (to boot into u-boot)

I have a board based on the AT91RM9200, and want to boot from SPI dataflash. The loader will proceed to boot u-boot (Wh...

2 comments posted 22yrs

posted by mail

2 comments posted 22yrs posted by mail

PIC If...then....else directive

Please can someone help. I'm quite new to PIC directives and I am having loads of trouble with the following "simple" c...

8 comments posted 22yrs

posted by gary99

8 comments posted 22yrs posted by gary99

Wireless data transfer

Infotech Resources Ltd. has good and cost effective solutions using nordic ICs for Wireless data transfer between two m...

0 comments posted 22yrs

posted by ruchattur

0 comments posted 22yrs posted by ruchattur

Porting linux on PPC 750 Cxe error after Freeing unused kernel memory: 248k init

Hi all, We are porting linux on to a PPC750 Cxe based board. We are successful enough to get the kernel messages on to...

1 comments posted 22yrs

posted by kiran

1 comments posted 22yrs posted by kiran

'best' control network? Devicenet vs Lonworks vs CAN vs Fieldbus vs Ethernet ???

no doubt this is a FAQ oft beat to death, but, assuming one wanted to control a network of about 10 i/o modules each wi...

14 comments posted 22yrs

posted by perfb

14 comments posted 22yrs posted by perfb

8- to 16-bit Embedded System Upgrade

Hi! We're on a new project with the golden opportunity to upgrade a system from an 8-bit 8051 to a 16-bit MPU TBD. The...

19 comments posted 22yrs

posted by karlbkeller

19 comments posted 22yrs posted by karlbkeller

FT245AM - lost USB device?

Hi, we are using a FT245AM connected USB printer in our embedded machine which is running Linux. For any reason sometim...

8 comments posted 22yrs

posted by klaus.hitschler

8 comments posted 22yrs posted by klaus.hitschler

germany only: searching for 68K emulator

Hi, for maintainance of a 68000 PLCC or DIP based board I'm looking to get an emulator or something else to load my cod...

1 comments posted 22yrs

posted by klaus.hitschler

1 comments posted 22yrs posted by klaus.hitschler

USB non-buspowered GND - what to do

Hi, I'm currently working on a selfpowered USB device and have just a quick question. Maybe I overlooked/missed some in...

5 comments posted 22yrs

posted by tobias_alte

5 comments posted 22yrs posted by tobias_alte

(Novice) Debugging timing-critical code

Regards... I need to code ISO-7816-3 (contact smartcards, data-link layer) in some MCU but I'm still pondering my optio...

1 comments posted 22yrs

posted by arielco

1 comments posted 22yrs posted by arielco

bit error detection

Can any one point me to some information on detecting bit errors and C or C++ algorithms that do this. I am familiar wi...

5 comments posted 22yrs

posted by bruce.trask

5 comments posted 22yrs posted by bruce.trask

MMC specification

Hello, I'me currently working on a embedded datalogger which writes data on a MMC card. the CPU is an MSP 430 from TI,...

2 comments posted 22yrs

posted by fonzarelli

2 comments posted 22yrs posted by fonzarelli

Sydney-X1 FPGA Computer, US$499 introductory price

BurchED announces the availability of the Sydney-X1 FPGA Computer, for the introductory price of US$499 ! The SYDNEY-X1...

1 comments posted 22yrs

posted by tony

1 comments posted 22yrs posted by tony

Need advice for a micro

Hello all, What do you think about the MPLAB ICD2 and the "USB Pic" in general ?! MSP430xxxx lowers, would you switch to...

4 comments posted 22yrs

posted by p_anagiotis

4 comments posted 22yrs posted by p_anagiotis

PIC Prototyping boards

We have about 54 prototyping boards left for the PIC16 series of microcontroller. Check them out at: http://www.microwid...

0 comments posted 22yrs

posted by arudzki

0 comments posted 22yrs posted by arudzki