Latest threads in Embedded Programmingshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Looking to work on some embedded projects as a volunteer
Hi, I have application development experience around 12+ years but I am still v ery fascinated of Embedded Systems / Linux Device Driver development. As su ch I am learning both and gained some...
6
|
10 years ago
|
6 | |
|
Lithium batteries for embedded systems
I'm building something that's approximately a laptop, with a total number of units of about 6, maybe one or two more. Laptops need batteries, as big (Wh) and as small (cm^3, kg) as possible, and this...
11
|
10 years ago
|
11 | |
|
3.5-6 inch TFT display with touch screen
I'm searching for a low-cost (1-5k pieces) small (3.5 to 5 inch maximum) TFT display with integrated touch-screen panel (resistive or capacitive... I don't need multi-touch). Do you have any...
19
|
10 years ago
|
19 | |
|
Developing Embbeded Driver board for ATIK314L+
Hi, I am currently working on a project in which I have to interface CCD camera ATIK314L+ with an embedded board. Camera ATIK314L+ is provided Cypress FX2 USB drivers support. I successfully completed...
—
|
10 years ago
|
— | |
|
Mature TCP/IP Stack for STM32
Hi We are working on a TCP/IP Gateway. Ideally we would like to use one of the free TCP/IP stacks that ST has made publicly available, but we are also open to 3rd party stacks We do however no know...
8
|
10 years ago
|
8 | |
|
OT: Cloud IT structure for a start-up?
Folks, Right now we are using an email provider and Dropbox for our start-up company. However, we'd like to get a more integrated solution that has all under one roof and preferably does not engage in...
22
|
10 years ago
|
22 | |
|
Programming the FT230 Chip
Has anyone built a product that uses the FT230 chip and requires it to be programmed? I'm looking at their "self powered configuration" (section 6.2 of the data sheet). It looks easy enough to...
2
|
10 years ago
|
2 | |
|
Small, fast, resource-rich processor
I'm working on a project that needs to have a pretty hefty amount of digital signal processing done in more or less real time ("soft" real time, if you must split hairs). For a variety of reasons I...
419
|
10 years ago
|
419 | |
|
STM32F4 DMA question
So I'm running into a response time issue on a serial port on an STM32F407. I was hoping that I could give myself more time to get to the ISR by piping the UART receive to the DMA. I got it set up to...
11
|
10 years ago
|
11 | |
|
ISO: UI/UX issues forum
Hi, I'm looking for a (?) forum concerned with UI/UX design issues, metrics/evaluation, etc. Ideally, one that isn't *solely* focused on the "technology". Searching USENET groups based on keywords...
—
|
10 years ago
|
— | |
|
Cheapest Microcontroller or Module Running Linux
Hi For a product with limited yearly qty, I am looking for a microcontroller or module that runs Linux or a derivative of that. Sofar I have come across the uClinux, capable of running on a Cortex M4...
7
|
10 years ago
|
7 | |
|
Autodetect slave devices on a bus network (RS485)
I have a bus network (RS485 based) with one master and N slaves. Each slav e has a different unique 32-bits serial number. I was thinking on a method for the master to autodetect the serial numbers of...
13
|
10 years ago
|
13 | |
|
CFP: ADAPT 2014 @ HiPEAC 2014
================================================================================ CALL FOR PAPERS ADAPT: 4th International Workshop on Adaptive Self-tuning Computing Systems January 22nd, 2014, Vienna,...
—
|
10 years ago
|
— | |
|
"short" pointers
Hi, [Probably should have posted this to c.l.c but those folks get too pedantic...] I'm looking for a *convenient* way of "SHORTening" pointers (to objects scattered through memory). All of the...
19
|
10 years ago
|
19 | |
|
Stack after reset for STM32F with gdb
I'm using Eclipse (Kepler release) GCC ARM Tools 4.7 OpenOCD 0.7.0 Its not clear how I can setup the Debug Configuration in order to ensure a Reset. Currently the Stack point is not being reset to the...
9
|
10 years ago
|
9 |