------------------ Hi Danny,
Came across your initial post a few days ago - & have followed the threads avidly. Most interesting!!! The majority of the replies have been suggesting you use the 'serial-to-parallel' data transfer method and that you also use either a PIC or an AVR micro - well I agree with the later (in principle) BUT (there's always a but, isn't there ...). you need to be aware that most of the PIC's and the AVR micro's have a "limited" amount of memory available - especially when you most probably need to store the message or graphic before you output it to the LED display - now in most of these micro's your control program takes up a fair chunk of the memory thus leaving a small (in some micro's - VERY samll) amount of free memory space to store the other things like 'variables', 'tables', as well as your 'message/graphic' data.
I agree with the many suggestions regarding 'multiplexing' of the LED array BUT driving the array by using the venerable 74LS595 (or 74HC595) serial-to-parallel shift register method is OK if you have plenty of speed and time to do the data setup & transfer in - with most of the micro's in question you may find this method a bit tight on time &/or speed - AND - the other thing to keep in mind is that your chip count CAN BE fairly large (38 or so 595's plus several control chips - already over
45 chips) which also means a larger PCB for your system, more costs, etc.After a few days twiddling with the concept I came up with the following - you might want to consider another method which could save you in costs as well as lower chip count and more FLEXIBILITY in what & how the LED MATRIX can be utilised.
The proposed method uses around 18 or so IC's; 72 FETS for row & column drivers; 1 x power FET - for PWM control of the LED supply; approx 90 resistors; a handful of small value capacitors; 384 LEDs - in a 8 x 48 matrix; plus either 1 or 2 PCBs.
As can be seen from the circuit diagram below - the 2 main IC's are the 62256 SRAM (32K x 8 bits static ram) & the microprocessor - an PICAXE 28X. The LED MATRIX uses 6 x 74LS574s for column drive & 1 x 74LS574 for row drive (these are 8 bit parallel tri-state registers). The "flexibility" spoken about above is - each LED in the matrix can be turned on or off individually - e.g. ALL on, 1 on, combination on, many on (in any position), PLUS a 'moving' display
- right / left / up / down, etc, are all possible display options.
The row & column drive FETs are 2N7000 N-Channel fets - 60 VDC (max), 400mA current (continuous) or
2A (pulsed), Rds(on) = 1.2 ohms, gate drive 2.4V, in a TO92 package. With each LED drawing 20mA 'on' current - column FETs drive 8 x LEDs = 160mA (total - all on); row FETs drive 16 x LEDs (@ 3 x FETs per row) = 320mA (total - all on). 2N7000 @ $0.35 in qty's 25+ 1 x MTP3055V N-Channel Power MOSFET is used to PWM the LED positive supply to the LED MATRIX - freq = 250 Hz, pulse width varies for brightness / dimness. With ALL leds on the max current drawn from the LED supply is approx 7.8A - the MTP3055V can handle 12A @ 60V DC.The 62256 SRAM is used for storing the data to be displayed on the LED MATRIX - 32K x 8 bits provides for up to 4600 different graphics displays - the matrix is setup as 8 x characters @ 8 bits high x 6 bits wide (= 384 LEDs). A full (384 LEDs) graphic/character display takes up only 7 x data bytes in the SRAM - 6 bytes for column drive; 1 byte for row drive.
The PICAXE 28X micro controls the LED display functions as well as the updating of graphics data to the SRAM. PWM output 2 (pin 13) of the PICAXE 28X is used to drive the MTP3055V MOSFET.
The 74LS138 IC's provide gating & control signals to the rest of the circuit as directed by the relevant PICAXE 28X Output portC pins.
I also suggest that the i2c pins (pins 14 & 15) of the PICAXE 28X be utilised to provide communication with an external PC via an PICAXE 18X chip (i2c pins 7 & 10) and a few extra IC's - all configured as a PC Parallel port - to - i2c converter.
I hope this gives you some more useful insights into how 'multiplexing' displays can be designed!!
The Circuit Diagram:
----------------------------------------------------------------------------------------
Ic9 LED MATRIX .--. (8 x 48 = 384) | | Col Col PICAXE o--o +--------------------+ 1 48 28X | | | | o|-/-------------------------------/-- Rw1 .------. | '--' 62256 | Ic7 o|-/-------------------------------/-- | | | .-------. | .--.o|-/-------------------------------/-- | | | .--.Ic10 | | | | |o|-/-------------------------------/-- | o----o | | |A0 D0| | | |o|-/-------------------------------/-- | | o--o +------+ +-----|----+ |o|-/-------------------------------/-- | | | | | |A7 D7| | | |o|-/-------------------------------/-- | | | | | |A8 | | '--'o|-/-------------------------------/-- Rw8 | o--o | '--' +---+ | | | | | | | | .--. | |A14 | | ######## ######## ######## | Ic14 | | | | | | | | | .-------. .------. .------. '------' | o--o +--+ | | | | Ic1 | | Ic2 | -------- | Ic6 | | | | | | | '---+---' '---+--' + + + '---+--' | | |Ic11 | Ic8 | | | | | | | | | '--' '-------' +---\--------+---------+-----+-+-+-------+ | 8 | .--.Ic12 Data Bus | | | o----o | ---------------------------------------------------------------- | | | | LED MATRIX Set-Up: | '--' | Col X | .--. | +Vled + | | | | o--o-o-+^+-+------+ Rw1a | o----o | | o = | ||| # = + | | | | === FET 1 ||-+ '--'Ic13 | | | ||<- FET X | +--------+ o---o-||-+ Ic1-7,10,11 = 74LS574 | | | Rw X | | | o--o+^++-------+ Rw1b | Ic8 = 62256 SRAM | | | ||| === | | | === FET 2 GND Ic9 = 74LS244 | | | | Col X | +----------+ Rw X + Ic12,13 = 74LS138 | o/p | | / = o-|-----------|---o | 1 | o--o+^++-------+ Rw1c +-->|---+ | Ic14 = PICAXE 28X | | ||| Led X | | | | === FET 3 ___ | | FETs = 2N7000 | | | +-|___|+ | | +--------+ +----------+ | Res X + | (created by AACircuit v1.28.4 beta 13/12/04
Oz-Rod