Lookinf for options for an Absolute Magnitude" or precision rectifier circuit.

I will not waste bandwidth posting a copy of all your moronic garbage posts- a very sick and irrational non-entity you are.

You are not doing "design work"- you are a F_Up, and damned joke.

Well- good that you found a reason for life- too bad it is all a joke firedrill- but be sure to raise a big storm over it so the hapless idiots who hired you can find out you are a moron -too.

GFOAD

What a F_CKING moron and pest!- I am so sure they look forward to fielding queries from you- with your ignorance, broken English, and overall moronic demeanor and mindset.

Oh my goodness- what a chatterbox you are!

Know to avoid you, is what you mean....

your

and

The customer seems to want to know if the unit will work over a very wide range. My nominal input (threshold) is 134 mV so I was considering a gain of about 4 up front. They are not likely to need the maximum of .6VRMS since that is more current than the wiring will safely support.

This is another item on the list to discuss with the customer. When I signed on to this project they'd already had a preliminary design review, now they say they have to get permission to make significant changes. I thought that until the 'critical design review' the project was a work in progress.

I will start to build a first article in the coming week. (Brass Board.)

I would prefer a different amp, for no other reason than I am more familiar with its performance. However Cost is not an issue. This unit sells for an increasable mark-up!

The good news is that they know they need this review and trust me to get the unit to qualification test, since I have done many of this type of project.

one's person's view is any more legitimate than an other's. In the end, it all comes down to evidence or in some cases the lack of it !

about me if he can fine someone to reply, since I never see his postings!

nonsense? Remember that Fred Bloggs has nothing at stake! I am the only one doing the design work on the electronics of a critical piece of aircraft safety equipment. The design I was told to "Modify, is ON aircraft now! Scares me, and I wasn't the one who did the deed!

All I can say is that you must have done/said something to upset him. Because he is not like this with everyone. I recollect that you wrote in reply to a message I posted "". Perhaps you did something like that to him too? If you call people stupid, sometimes they will take offence and return the favour.

It is best to respect other people's points of view - you do not necessarily have to hold them too. Remember that they may hold them just as sincerely as you.

say that any one's person's view is any more legitimate than an other's. In the end, it all comes down to evidence or in some cases the lack of it !

say to me, or about me if he can fine someone to reply, since I never see his postings!

deliberate nonsense? Remember that Fred Bloggs has nothing at stake! I am the only one doing the design work on the electronics of a critical piece of aircraft safety equipment. The design I was told to "Modify, is ON aircraft now! Scares me, and I wasn't the one who did the deed!

him. Because he is not like this with everyone. I recollect

return the favour.

necessarily have to hold them too. Remember that they may hold

You are now dealing with something you have no knowledge of. FB started this by use of foul language, name calling, and calling me stupid. You are clearly unaware of what you as wading into. You should be talking to Fred!

However I would note: pot / Kettle -- Black! Your engaging in the same behavior you criticize!

Remember HE is the one who attacked me, not that he has limited himself to me, he is not inclined to be polite or extend respect. He is therefore not deserving of respect. You should choose your allies with more care! He is NOT your friend. Or are you another clone of FB? He has so many it is hard to keep track.

he's

He 'IS' history then.

I read in sci.electronics.design that richard mullens wrote (in ) about 'Lookinf for options for an Absolute Magnitude" or precision rectifier circuit.', on Mon, 7 Feb 2005:

It takes very little to do that. Practically nothing.

He is with nearly everyone. Your turn will come.

But he does put out very good designs, and very quickly, too.

I guess that in 8 years time when I'm as old as you are now, I'll have become less tolerant of other people's views too.

For the moment I read what you say - even though I don't always agree with it - you come across as a likeable rogue.

That's good information. Thank you.

FauxPhred? Or maybe Fox(news)Fred? (oh, I can't wait for the spew!)