Where would I find a pot (rheostat?) to replace the twist control in a joystick?

Took apart a Logitech Wingman Extreme Digital 3D joystick to see if I could= do anything about the responsiveness of the yaw/twist control.=20

The piece that controls this is a pot or rheostat (please advise of the cor= rect name) - the axis of the piece mounts to a center rod inside the joysti= ck handle, has a nib on one end that fits into a slot in the handle structu= re that's responsible for rotating the piece. It seems that it only ever se= es a small portion of its potential travel - wondering if I can find one th= at has a "quicker" response - i.e. will change the voltage more with less t= wist.

Any idea where to get pieces like this might be a match or close enough to = be retrofitted?

Thanks.

Reply to
docsavage20
Loading thread data ...

anything about the responsiveness of the yaw/twist control.

name) - the axis of the piece mounts to a center rod inside the joystick handle, has a nib on one end that fits into a slot in the handle structure that's responsible for rotating the piece. It seems that it only ever sees a small portion of its potential travel - wondering if I can find one that has a "quicker" response - i.e. will change the voltage more with less twist.

retrofitted?

Pot (short for potentiometer) is the correct term. Rheostat is another name for the same thing, but that name is usually used for high power wire-wound devices.

A source for such devices is Digikey

formatting link
There are other as well. You may also be able to achieve your desired effect by adding some resisters in the circuit in series or parallel with the current pot or perhaps even with no hardware changes at all by changing something in software. It would depend on the actual design of the joystick and its software driver. Unfortunately, I am not familiar with either one. Good luck.

Pat

Reply to
Pat

NO !

A potentiometer is specifically referring to a three terminal device, which is a variable resistor. In most cases the leftermost terminal is grounded, and the input usually goes to the right terminal. The output is taken off the wiper (center terminal). In some low power applications they apply the input to the wiper because of the impedances involved (such as an electric guitar) , but if you do it that way with a buffered signal you need resista nce to make sure you don't burn up the bottom end (near the left terminal).

A rheostat by definition is only a variable resistor, it only uses two term inals. It will have three terminals usually but the crux of the matter is t hat only two are used in the circuit in question. It can also go either way , with resistance increasing or decreasing with clockwise rotation. They ar e rarely used in apps with active devices.

There are diferent curves for each, linear, log or audio, and each has it's specific application(s) in a given circuit, depending on what you need. In old planetariuums (like 1960s) the lights were frequently fed by rheostats with a logrythmic taper. In your audio equipment, they are almost always p otentiometers, although there are a few exceptions inside like sometimes th e bias control. What the user sees are pots. Rarely maybe a variable loudne ss contour control (on really expensive stuff) might be a rheostat.

But in that application it is the same part, but only with two terminals us ed. Another application where a rheostat was used is in the dashlights of v ehicles for dimming. They have been replaced of course by switched mode con trollers in the newer cars because of efficiency. Those are most likely con troled by a pot rather than a theostat, but that's because they are feeding a transistor circuit.

J
Reply to
jurb6006

Oops, forgot about the OP.

Does the thing have three wires or two ? What's more some of these have spe cial mounting and all that. What's needed is a picture. It's possible Digik ey has something, but not very probable.

There are places on the net that carry parts for these things, however if i t is not defective and you just want to change the "parameters" so to speak , that's a different story. Maybe if it is just a rheostat (two wires) the range can be changed by just changuing the resistive element. This is not a ll that likely.

To change the range, it's better to look for a series resistor off the rheo stat and just change that to a lower value. If it is being used as a pot it is a little bit trickier, but can be done.

We need the wires counted and a picture, plus a full model number so that m aybe there is a print or something on the net.

J
Reply to
jurb6006

... and any useful quoting.

Reply to
Allodoxaphobia

ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.