isplsi1016

Hi There, I have Orcad Express CIS 7.2 and I want to program Lattice ispLSI1016 using it. I already have the schematic for it in Orcad Express. Also I have the programmer for 44 pin isp1016. I was wondering if someone can guide me as to what steps I need to take after this. thanks

schrieb im Newsbeitrag news: snipped-for-privacy@g43g2000cwa.googlegroups.com...

Go to

Download the ispLever Software. Install it. Get a licence (its free) Create a project. Compile the schematics Download the JEDEC file. Njoy.

Regards Falk

Hey Man Thanks for the reply. Just to make sure will this be ispLEVER-Starter Synplify Synthesis Module (May 2005) because as far as I know ispLSI1016 is CPLD

ispLSI1016 may not be supported by the recent *free* software releases? But you can program the device with the downloadble programming software.

Which programming software are you refererring to? I am a novice in this field and this is something that I have inherited. So if you can be more specific that will be great. thanks

schrieb im Newsbeitrag news: snipped-for-privacy@z14g2000cwz.googlegroups.com...

Hmm, Mika is right. The free "ispLever" does not support the rather old 1016 anymore. Contact the support. When I did so, they offered my to give me a location where I can download the old version, which does support the old devices. As for the programming tool, its called ispVM (if I remember correctly). This tool allows you to programm the devices, similar to an EPROM programmer. But thats all. If you dont have a JEDEC file (*.jed) you need to compile/fit your VHDL/Verilog/Schematics using ispLever.

Regards Falk

schrieb im Newsbeitrag news: snipped-for-privacy@f14g2000cwb.googlegroups.com...

I duno.

Can Orcad Express CIS 7.2 be used instead of ispLEVER?

"Falk Brunner" schrieb im Newsbeitrag news: snipped-for-privacy@individual.net...

not as easy - the Lattice support told me once that older devices like ispLSI1016 can be 're-enabled' in the new software, by editing some textual conf file, but I never got the details how to do this :(, and it was for ispLever 4.x something not sure if it is still doable for 5

antti

As far as I know, it is still do-able. I suggest on the other hand to contact your local FAE (or distributor). They will certainly help you further.

Luc

Will ispLever work with something so old as 1016 ?

I have also a couple of 2128's. Does it work with 2xxx also ?

ispLever 4.2 still supports the 2k series.

Regards Falk

ispLever 5.0 also has 1k and 2k support..not for the oldest one though...but I could use the 1016E LC44 type for generating a JEDEC file for my old ispLSI1016 PLCC CPLD's (o;

rick

Brane2 ha scritto:

Last summer I had to work with an old 1032 PLD for my thesis. Lattice sent to my university lab the ispLever software, but it did not have the support for that old device. So they sent me the so called "Obsolete package", which added the support for older devices. Then it was possibile to use the 1032 device. If you want I can send you that package.

Bye

-- Per rispondermi via email sostituisci il risultato dell'operazione (in lettere) dall'indirizzo

-*- To reply via email write the correct sum (in letters) in the email address

yes that will be a great. will I still need isplever 5.0 or just the obselete package will be enough for ispLSI1016? Thanks

" snipped-for-privacy@gmail.com" ha scritto:

The package is an add-on to ispLever, so you also need it. I don't remember the version of ispLever I used. I hope the Obs. package Ihave works also for your version of ispLever.

Tomorrow I should be able to send you the file to your email.

Bye

-- Per rispondermi via email sostituisci il risultato dell'operazione (in lettere) dall'indirizzo

-*- To reply via email write the correct sum (in letters) in the email address

thanks a lot

" snipped-for-privacy@gmail.com" ha scritto:

I'm sorry but your email account does not accept attachments (even of small size: 600 kB):

From: Mail Delivery Service Subject: Delivery Status Notification To: XXXXXXXXXX Date: Mon, 6 Jun 2005 21:55:24 +0200 Message-ID: MIME-Version: 1.0 Content-Type: Multipart/Report; report-type=delivery-status; boundary="========/41BDB2AB026BC03D/smtp1.libero.it"

- These recipients of your message have been processed by the mail server: snipped-for-privacy@gmail.com; Failed; 5.3.4 (message too big for system)

Remote MTA gmail-smtp-in.l.google.com: network error

- SMTP protocol diagnostic: 552 5.7.0 Illegal Attachment c3si3192990rne

Reporting-MTA: dns; smtp1.libero.it Received-from-MTA: dns; localhost (172.16.1.82) Arrival-Date: Mon, 6 Jun 2005 21:55:18 +0200

Final-Recipient: rfc822; snipped-for-privacy@gmail.com Action: Failed Status: 5.3.4 (message too big for system) Remote-MTA: dns; gmail-smtp-in.l.google.com Return-Path: XXXXXXXXXXXXXX Received: from localhost (172.16.1.82) by smtp1.libero.it (7.0.027-DD01) id 41BDB2AB026BC03D for snipped-for-privacy@gmail.com; Mon, 6 Jun 2005

21:55:18 +0200 Received: from pc-fabio.libero.it (151.37.229.89) by smtp2.libero.it (7.0.027-DD01) id 41BF65E4080BEC52 for snipped-for-privacy@gmail.com; Mon, 6 Jun 2005 21:55:41 +0200 Message-Id: X-Sender: XXXXXXXXx (Unverified) X-Mailer: QUALCOMM Windows Eudora Version 5.0.2 Date: Mon, 06 Jun 2005 21:29:55 +0200 To: snipped-for-privacy@gmail.com From: Fabio XXXXXXXXXXXX Subject: Obsoleto package - Part 1/3 Mime-Version: 1.0 Content-Type: multipart/mixed; boundary="=====================_386626589==_" X-Virus-Scanned: by amavisd-new at libero.it serv3

-- Per rispondermi via email sostituisci il risultato dell'operazione (in lettere) dall'indirizzo

sorry for the trouble. i guess its because of my options. try it now. thanks