The types of bus bars you maybe referring to are to have their unused holes between the load points, occupied by electrical bolts and tighten in position to act as part of the bus conduit path.
Those are gang bus bars. Smaller gang bars usually come with 1/4-20 or 10-32 screws, put in place.
Jamie
Change is inevitable, except from a vending machine.
You are absolutely 100% full of baloney. You must be the group's baloney conduit.
Such elements as mounting bolts, and the rails they mount on,and their bolts, are of high electrical resistance, and are not in any way considered as part of the electrical path. The devices in the rack are ALL grounded chassis through their own, dedicated attachment wires and THOSE currents are what the bus bar is for, and the rack chassis never carries the faults of any of its devices. Even the chassis has its own jumper TO the bus bar. The electrical power feed for the rack is where the fault is carried FROM the bus bar.
Each powered device in the chassis gets a dedicated fault return wire from its hard, internal chassis to the bus bar. Faults are never carried by the rack chassis assembly.
The types of logic you use are as bogus as your "results" are. You need to have your brain tightened in position. Re-do everything from about the third grade on up.
You're babbling, again.
What does this have to do with gang bus bars?
You know, I wrote a whole reply for you, just to make an attempt to educate you how ever, it's apparent what others are saying must have some validity.
All I can say is, if you do this kind of work as a professional, I dearly hope you are supervised by some one that knows better, than you, obviously.
Jamie
If you are supposed to learn from your mistakes, why do some people have more than one child?
It only affects intoxicated electrons, flowing under the influence :-)
Sometimes a picture is worth more than two pages of math.
-- Regards, Joerg http://www.analogconsultants.com/ "gmail" domain blocked because of excessive spam. Use another domain or send PM.
Interesting how in your last two responses, you refuse to address the question posed to you, and spend your time and the entire posts attacking me. Leans toward you not knowing a goddamned thing about it.
Then, you finish off like a drunken jock idiot. Come back when you can actually write a complete sentence.
Answer the question, babble boy. Otherwise shut the f*ck up, wuss.
I calculated that your retarded ass would be the first to respond to that post.
I study Cosmology as a hobby, John. I have more on the ball with math than you *ever* will.
All bluster, as usual. You are innumerate; you never specify amounts or quantify effects.
John
What ever the question was, it wasn't worth my time to read it, obviously..
To put it in your view, you are what you are.. "Bull Shit", and you sure know how to fling it around.
Bye now, this has been a worthless response from me, because I know you are too dense to understand.
I won't tell you to stop spreading your bull shit around, because that isn't me how ever, you may want to stop embarrassing yourself. You really do look like an idiot.
Jamie
Cosmetology mostly deals in imprecise quantities such as "dabs".
Best regards, Spehro Pefhany
-- "it's the network..." "The Journey is the reward" speff@interlog.com Info for manufacturers: http://www.trexon.com Embedded software/hardware/analog Info for designers: http://www.speff.com
I could easily quantify the effect that I have had on your pathetic ass.
You know nothing about me, yet claim blustering.
You exhibit the very epitome of the definition of the term.
Yet another illiterate twit.
That's why you stay on 'the short bus'?
-- For the last time: I am not a mad scientist, I'm just a very ticked off scientist!!!
Pretty amusing really, since this thread got going by my replying by mistake to a post from 2003!
Cheers
Phil Hobbs
ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.